Thankfully, Submarine 4.0 has performed well in a range of environments from swimming pools and water tanks to a nearby river. With lots of weeds and obstructions on the river bed, he was keen to avoid collisions, especially as it cost more than 600 EUR. To prevent entanglements while on manoeuvres, he attached a magnet on the inside top of the submarine frame so he could ‘fish’ the craft out of danger, if needs be. He added 580 g of tungsten pellets to make the submarine dive gently, making adjustments using the syringe. Weighed on a kitchen scale, the submarine was 826 g, with a displacement of 1614 g. For this version, he splashed out on expensive 2.5 mm tungsten pellets weighing 18 g/cm3. In Submarines 2.0 and 3.0, he used lead pellets to provide extra weight, but they were quite sizable and took up valuable space inside the submarine’s frame. Raspberry Pi provides enough juice to power the board, so he decided to discard its LiPo battery in favour of a LEGO waterproof rechargeable battery pack. A SparkFun TFMini-S Micro laser sensor provides a second means of measuring the submarine’s depth, but its accuracy is affected by the murky environments in which he was using it.Ī more successful purchase was the radio board he harvested from a cheap Chinese toy submarine, having chosen it for its 27MHz radio frequency (needed to penetrate water) and its aesthetically pleasing controller. It connects to Raspberry Pi Zero 2 W via I2C. LEGO gears were fitted to control the syringe that would adjust the buoyancy.Īn absolute pressure sensor (which measures pressure relative to a vacuum, and is unaffected by the ambient pressure) is used to track the submarine’s depth. The basic acrylic cylinders were precision-cut and end pieces with rubber seals attached to form a waterproof unit. He now says wireless LAN is “an absolute necessity” which “made the development process a lot faster.” Underwater flying machineĪ fair amount of time and effort went into creating the submarine’s beautiful transparent acrylic case with tightly fitting and invisible end caps. He soon found the wireless LAN connectivity invaluable when tweaking the PID parameters and updating any Python code without having to physically connect to the Pi Zero 2 W via USB (which would have involved carefully extracting everything from the precision environment he’d created). He planned a similar setup here, to monitor and control the submarine’s depth. That will help the control loop.” This loop is also the reason for using Raspberry Pi: as we reported last issue, he had recently made an impressive inverted pendulum that uses a PID (proportional integral derivative) control loop running on Raspberry Pi Zero 2 W to accurately measure and compensate for constantly changing speed, location, and pressure levels. Most importantly, “you can measure the piston position with a LEGO EV3 motor that contains a tachometer. However, it had proved a more stable setup and would not compress under pressure when submerged. He settled on the last method for Submarine 4.0, despite the difficulty of gauging the neutral buoyancy point. The first three variously used propellers to add or reduce buoyancy (“gravity and buoyancy stay always the same while the propellers exert force”) a balloon, and an air compressor to adjust the amount of water displaced, thereby controlling whether the submarine sinks or rises and a piston ballast to suck in more water to add weight and increase the sub’s gravity. Feel free to use the instructions and build any of these.This is the fourth LEGO submarine design he has completed. I added some pictures for some tricky steps. They might not be perfect, I’ll take any comment about these. This is my first try in creating Lego type instructions using Studio 2.0. Some “weeping begonia/yellowbell” plant.With the rest of the parts, I thought it could be fun to design some deep sea creatures. I used some of the extra parts from the set as well. The submarine deploys some gimmicks like the torpedo, big bomb (sorry not functional, lol) and the ladder on the side to access the platform The elevation fins are actuated thanks to the periscope but have a limited movement. When pushed lightly, the submarine can steer thanks to the small 42610 wheels, rather than skidding/gliding. The rudder/fin is linked to the steering wheel. The propeller is driven by a wheel at the front, which also activates the engine. I thought the Charger’s got plenty of Technic panels and I could make a submarine too out of its parts, right in between these mentioned.įunctions are pretty simple and mostly hidden inside the submarine shell. based on 42120 rescue hovercraft by Nequmodiva based on 42082 “big red” rough terrain crane by Klimax Inspiration for this MOC came from 2 other submarine MOCs:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |